Showing all 8 results

Show sidebar

Tesseract 1.1.4 Version Motherboard for Ender-3 V2/Ender 3 Pro/Ender-3/Ender-5 Printer


Creality Ender 3/PRO Motherboard V1.1.4 replacement board features Control and drive, Loaded with default firmware from Creality3D, ready to print. The circuit board is optimized by circuit, effectively solve the heating problem. It’s comes with special power chip, support 24V input voltage and newest version with super silent TMC2208 driver.

Features :

Control and drive
Stable performance
High performance and low consumption
Cooling system
Multiple protection system
Well-selected material

Packing List:1 x Creality 3D Ender 3/PRO Motherboard Standard V1.1.4

Tesseract 1.1.5 (4.2.7) Version Motherboard 32 Bit Silent board for Ender-3 V2/Ender 3 Pro/Ender-3/Ender-5 Printer


Now print on your ender 3 using this upgraded motherboard for a wonderful print experience with minimal noise. The TMC driver is super quiet! Bootloader installed (ISP/USB Arduino). Suitable for Ender-3/Ender-3 Pro/Ender-5. This new upgraded silent motherboard is currently not pre-installed on Ender 3, Ender 3 Pro printers. At this point, the silent motherboard is a separate upgrade for all Ender’s. The firmware for Ender 3 /Ender 3 Pro / comes pre-installed NOW You just plug them in and start printing! 1x Silent Mainboard(V4.2.7)

Tesseract 370 x 375mm Silicon heated bed pad with digital controller for Creality Ender 5


370 x 375mm size suitable for Ender 5, comes with 24 Position holes and can be easily mounted below the existing metal bed

370 x 375mm size Maximum power 1200W. The maximum heating temperature can reach up to 120C (Celsius Degree)

The back side has 3M adhesive glue, which can directly stick to the heated bed. Make sure to clean heated bed properly before sticking the pad for better adhesion.

Comes with a controller to set and control the temperature. This allows for ease of use as you do not need to make major modifications to the existing machine controller before use.

Tesseract 508X508mm Silicon heated bed pad with digital controller for Creality CR-10S5


Silicon heated bed with digital controller for Creality CR-10 S5 to let heated bed up to 100C with 28 postion holes that fit perfectly on the machine Description: * 508-508mm suitable for CR-10S5, comes with position holes to be easily mounted on machine bed * 508-508 Maximum power 1200W * The maximum heating temperature 120C (Celsius Degree) * The back side is 3M adhesive glue, can directly stick to the heated bed. * The heated bed Maximum temperature resistance is 200C, with suitable long term working temperature condition under 180C * The pad comes with 24 position holes, that allow it to be easily mounted on CR10S5 if you order 510-510mm * To ensure safety , the plugs are 3 pins, please choose Plug type according to your area * Controller has EU plug, voltage is 220-240V * For safety, When using first time, please test to find a suitable temperature for you to use

Tesseract MKS GEN V1.4 Controller Board Motherboard For 3D Printer (Pack of 1)


It gather 2560 and ramps1.4 on a same board, which solved the Ramps1.4 combination interface problem that easily out of order.

Circuit board uses the high quality of 4 layer board optimizing heat dissipation.

Dedicated power chip, supports 12V-24V power input, the voltage converter chip solves the heat problem Ramps.

Flexible power supply from 12 – 24V. With onboard ATmega2560.

The firmware can use open-source firmware Marlin, ramps1.4 identical configuration and can directly replace Ramps 1.4.

Tesseract Thermistor Cartridge ATC Semitec 104GT-2 ,104NT-4-16C054RT for V5 V6 Volcano Sensor Cartridges Size 3mm x 15mm


Maximum temperature : 300°C, Beta value : 4267 K, Resistance at 25 degree C : 100 Kohms

Encapsulated in a 3mm steel cartridge. Head part is insulated with fiberglass sleeving in the, and terminated with a connector.

This makes it particularly easy to disconnect your entire HotEnd without the need for re-wiring. Operating temperature is able to reach 300°C.

Suitable for PLA, PETG, ABS, TPU, HIPS , PC, PC-ABS, etc. material.

Marlin configuration * 5 : 100K thermistor – ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) #define TEMP_SENSOR_0 5


Tesseract Thermistor PT-100 Thermocouple Sensor (For Ultimaker 2 UM2) with Stainless Steel Shell, Size 3mm x 15mm, with KF-2Pin Terminal, Wire Length 1500mm


PT100 special PTFE silver-plated shielded wire. Range of Temperature: 0~450 Degree

The maximum temperature of teflon is approx. 260 degrees. To ensure the pt100 to measure the higher temperature, we use double fibreglass sleeving and 1000-degree thermal adhesive to protect the wire. To make working temperature is able to up to 450 degrees, and avoid the short-circuit or damage during operation.

The PT100 B sensor measures the temperature on the hot end of the Ultimaker 2

Please be aware that a PT100 is not the same as a thermistor and unless your electronics explicitly supports RTD Sensing devices you will need an amplifier board.

The Ultimaker 2 uses PT100 sensors by default, and this sensor allows you to connect your E3D Hotend and Ultimaker electronics with no alteration to the electronics or firmware of the Ultimaker 2.